Amatrol’s Basic Pneumatics training system (85-BP) introduces pneumatic principles through a combination of Amatrol’s top-flight multimedia curriculum with hands-on industrial pneumatic skill-building. Topics covered in this learning system include single-acting cylinder circuits, pressure vs. cylinder force, and flow control valves, while the panels can be used to practice skills such as connecting and operating a needle valve to control actuator speed.
Industrial Pump Maintenance and Troubleshooting
The Gear Pump Learning System (95-PM1-F) covers the function, operation, installation, and maintenance of the versatile gear pump. This low maintenance pump can transfer a wide array of fluids and fluid viscosities for spraying, recirculating, cleaning, and fluid transfer applications. One of the most common applications of a gear pump is in an automobile’s automatic transmission. This industrial pumps training system also provides information on pump inspection, pump disassembly, pump maintenance, and pump troubleshooting, as well as how to select the proper gear pump for an application and how to calculate theoretical and actual flow rates.
Pump Maintenance & Troubleshooting Skills
The Magnetic Pump Learning System (95-PM1-G) covers the magnetic pump, which uses a magnetic coupling to prevent direct contact between the motor drive shaft and the pump impeller. This feature eliminates any possibility of leakage or seepage and makes the magnetic pump an ideal selection for pumping hazardous chemicals that could harm the environment or for expensive liquids where it is important to reduce loss. This industrial pumps training system explains the function, operation, installation, disassembly, inspection, and maintenance of a magnetic pump.
Additional topics include: how to properly align the magnetic coupling; how to troubleshoot problems; how to select the correct magnetic pump for an application; how to determine a pump’s flow/pressure characteristics; and how each component of the pump factors into the overall operation.
Pump Maintenance Skills
The Centrifugal Pump with Stuffing Box Learning System (95-PM1H) covers a pump design that, in spite of the modern mechanical seal, remains widely used in industry due to its cost-effectiveness and ability to avoid catastrophic failure. This feature makes it an ideal design for fire departments in fire pump applications. This industrial pumps training system explains the installation, function, and maintenance of a centrifugal pump with a stuffing box.
Additional topics include: how to troubleshoot this pump design; what the flow/pressure characteristics of a centrifugal pump are; and how to startup and operate a centrifugal pump with a stuffing box.
The model 950-PM1 Centrifugal Pumps Training System teaches skills related to centrifugal pumps training, which are used in almost every industry to transfer non-hydraulic fluids of various types from one place to another. Students learn a comprehensive set of industry-relevant skills including how to operate, install, maintain, troubleshoot, analyze performance, and select centrifugal pumps as well as system design.
The model 950-PM1 includes a centrifugal pump, mobile test workstation, student learning materials for both theory and lab, and teacher’s guide. This centrifugal pumps operation and maintenance training system uses industrial quality components such as a cast iron centrifugal pump to help students become better prepared for what they will encounter on the job.
Amatrol’s Rigging 2 Learning System (95-RGB2) adds to the first Rigging training system (950-RGB1) to offer a comprehensive learning experience, to teach rigging safety training and industrial crane operation skills, and to help learners prepare for certifications. This hands-on Rigging training system expands on the initial offering of rigging knowledge to include synthetic slings, equipment movement, and industrial cranes. Proper rigging techniques are vital for efficient movement of loads and workers safety.
This Crane Operation training course includes two synthetic slings, four load protection pads, jack, lever dolly, and much more! These components will be used to explore topics such as synthetic sling operation, equipment movement using roller bars and dollies, and crane operation signals. In addition to equipment and printed curriculum, this industrial system offers a student reference guide, instructor’s manual, installation guide, and an optional online rigging training course.
Amatrol’s Rigging 3 Learning System (95-RGB3) adds to the initial hands-on rigging training systems (950-RGB1 and 95-RGB2) by including hands-on wire mesh sling skills, rigging knots training, and rigging safety skills. This advanced rigging training system provides learners with additional components and skills to further expand their understanding and competency of rigging. Proper rigging techniques are vital for efficient movement of loads and workers safety.
This advanced rigging training system includes a rope system, D-shackle, steel tubing, a metal mesh sling, and much more! These components will be used to explore topics such as making a long, short, and eye splice in a fiber rope, describing the function of a tag line, and learning how to assemble and lift a load using a wire mesh sling. In addition to equipment and printed curriculum, this system offers a student reference guide, instructor’s manual, installation guide, and an optional online eBook.
Amatrol’s Solar Site Analysis Training System (95-SA1) teaches learners both the theoretical knowledge and hands-on skills they will need to analyze and choose suitable locations for solar arrays and components. Learners begin by studying how to conduct a preliminary site assessment, including applicable codes, jurisdictional authorities, permits, and licenses required for solar energy system installations.
Learners will also use real-world equipment, like the Solar Pathfinder sun path calculator, to perform and interpret a shading analysis in order to determine suitable locations for electrical photovoltaic and solar thermal components. The included multimedia curriculum also teaches other relevant skills, such as developing site layout drawings.
The Solar Thermal Cold Water Supply Station training is designed to reduce the temperature of hot water from the open loop (950-STOL1), closed loop (950-STCL1), or installation solar thermal (950-STF1) learning systems and feed it back to the learning system at a temperature and pressure that is similar to a city water supply. This system will enable the three solar thermal learning systems to be self-contained.
The Solar Thermal Cold Water Supply Station training includes the frame, AC pump, AC chiller, water storage tank, ball valves for shutoffs and bypasses, relief valve to adjust temperature and pressure output, temperature gauges, a pressure gauge at outlet of chiller, control unit, ground fault circuit interrupter, and an AC circuit breaker with lockout / tagout.
Amatrol's AC/DC Electrical Learning Systems 1 and 2 (96-ADE1 and 96-ADE2) cover the fundamentals of electricity, such as electric measurement training and basic electrical cir-cult training, as well as Inductance, capacitance, and transformers. Electricity Is the most widely used utility and the demand will continue to increase as technology continues to grow. This means that more engineers and technicians will be needed to Install, develop, and maintain electrical devices. These learning systems include a large array of Industrial electrical power and control components, typical of what learners will find In real world applications. This hands-on experience Is Invaluable In today's workplace.
Amatrol's Computer Aided Design (CAD) 1 – SolidWorks learning system introduces solid modeling by describing the function of solid modeling software and the features of solid modeling. Solid model creation is taught by having the learner use sketch commands and tools to create a sketch and extruded boss/base features to create a solid model. Solid model features such as drawing planes; extruding cut features, fillets and chamfers; and revolved features are explored. Also included are topics such as multi-view drawings, dimensioning, and title blocks.
Pages
-
Item Number:85-BP -
Item Number:85-EHThe Electro-Hydraulics training system includes an electrical control panel with relay control components and an electrical valve module with solenoid-operated hydraulic directional control valves and electrical/electronic sensors. These components will be used to study a variety of topics including electrical control systems, basic control devices, power devices, control relays, sequencing control, timer control, pressure control applications, and circuit applications. -
In the rare event that a burning ember or spark is drawn into the fume extraction unit, there is the possibility that debris in the filters could ignite. Although any resultant fire would typically be retained within the fume extraction unit, this would cause significant damage and in extreme circumstances, the risk may extend beyond the extraction unit. For processes where such risks have been identified, additional protection in the form of an in-line firebox is an additional precaution.
-
The BOFA inline pre-filter 1000 has been designed specifically for applications that generate high amounts of dust or particulate.
This inline filter unit is positioned alongside the main BOFA fume filtration system to increase the overall filter capacity and extend the life of the main filters. The DeepPleat DUO pre-filter incorporates a massive drop-out chamber within the filter, having a volume area of 15ltrs. Above the drop-out chamber but still within the housing there is a sealed 200mm deep pleat layer of F8 media giving a surface area in excess of 30 sq meters.
-
The BOFA inline prefilters have been designed specifically for applications that generate high amounts of dust or particulate. -
Item Number:LMT-300LMT-300 CNC Mill-Turn is a cutting-edge aluminum cutting machine -
Item Number:LMV-300 CNCThe LMV-300 CNC machine dubbed “Quicksilver” delivers high rigidity, high accuracy and high-speed machining for all your cutting needs. The entire machine’s construction stably attaches to a granite bed thus dampening vibrations and making the machine a robust system. The cornerstone of the machine is that it is literally made from stone.
-
A compact 3 axis CNC micromill milling machine with totally enclosed interlocking guards - the ideal introduction to small part CNC manufacture. Variable spindle speeds and feedrates make the MicroMill ideal for cutting resistant materials such as wax, plastic, acrylic, aluminum and free cutting alloys. -
A compact 2 axis CNC lathe, with totally enclosed interlocking guards - the ideal introduction to small part CNC manufacture. Variable spindle speeds and feedrates make the MicroTurn ideal for cutting resistant materials such as wax, plastic, acrylic, aluminum and free cutting alloys. -
Denford's high-spec / low-cost solution for all your routing, milling and engraving needs. The MRC 40 has a powerful 500W spindle motor and offers high speed manufacture linked with a large working envelope. This versatile machine handles small engraving jobs, and the large working envelope and Z axis capability (110mm) is perfect for the manufacture of large 3D designs. Set-up and tool changes are a simple process, and the MRC 40 has a host of optional extras for specialist applications.
